Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Mitsuhara, Masatoshi*; Kurino, Koichi*; Yano, Yasuhide; Otsuka, Satoshi; Toyama, Takeshi*; Onuma, Masato*; Nakashima, Hideharu*
Tetsu To Hagane, 109(3), p.189 - 200, 2023/03
Times Cited Count：0 Percentile：0(Metallurgy & Metallurgical Engineering)Oxide Dispersion Strengthened (ODS) ferritic steel, a candidate material for fast reactor fuel cladding, has low thermal expansion, good thermal conductivity, and excellent resistance to irradiation damage and high temperature strength. The origin of the excellent high-temperature strength lies in the dispersion of fine oxides. In this study, creep tests at 700 or 750
C, which are close to the operating temperatures of fast reactors, and high-temperature tensile tests at 900 to 1350 C, which simulate accident conditions, were conducted on 9Cr ODS ferritic steels, M11 and MP23, and 12Cr ODS ferritic steel, F14, to confirm the growth behavior of oxides. In the M11 and F14 creep test samples, there was little oxide growth or decrease in number density from the initial state, indicating that dispersion strengthening by oxides was effective during deformation. After creep deformation of F14, the development of dislocation substructures such as dislocation walls and subgrain boundaries was hardly observed, and mobile dislocations were homogeneously distributed in the grains. The dislocation density increased with increasing stress during the creep test. In the high-temperature ring tensile tests of MP23 and F14, the strength of both steels decreased at higher temperatures. In MP23, elongation decreased with increasing test temperature from 900 to 1100 C, but increased at 1200 C, decreased drastically at 1250 C, and increased again at 1300 C. In F14, elongation decreased with increasing temperature. It was inferred that the formation of the 
-ferrite phase was responsible for this complex change in mechanical properties of MP23 from 1200 to 1300 C.
Yano, Yasuhide; Uwaba, Tomoyuki; Tanno, Takashi; Yoshitake, Tsunemitsu; Otsuka, Satoshi; Kaito, Takeji
Journal of Nuclear Science and Technology, 9 Pages, 2023/00
Times Cited Count：1 Percentile：72.91(Nuclear Science & Technology)The effects of fast neutron irradiation on tensile properties of modified 316 stainless steel (PNC316) claddings and wrappers for fast reactors were investigated. PNC316 claddings and wrappers were irradiated in the experimental fast reactor Joyo at irradiation temperatures between 400 and 735 C to fast neutron doses ranging from 21 to 125 dpa. The post-irradiation tensile tests were carried out at room and irradiation temperatures. Elongations of PNC316 measured by the tensile tests were maintained at an engineering level, although the material incurred significant irradiation hardening and softening. The maximum swelling of PNC316 wrappers was about 2.5 vol.% at irradiation temperature between 400 and 500C up to 110 dpa. Japanese 20% cold-worked austenitic steels, PNC316 and 15Cr-20Ni, had sufficient ductility and work-hardenability even after above 10 vol.% swelling, while they had very weak plastic instabilities.
Yano, Yasuhide; Hashidate, Ryuta; Tanno, Takashi; Imagawa, Yuya; Kato, Shoichi; Onizawa, Takashi; Ito, Chikara; Uwaba, Tomoyuki; Otsuka, Satoshi; Kaito, Takeji
JAEA-Data/Code 2021-015, 64 Pages, 2022/01
JAEA-Data-Code-2021-015.pdf:2.6MB
From a view point of practical application of fast breeder reactor cycles, which takes advantage of safety and economic efficiency and makes a contribution of volume reduction and mitigation of degree of harmfulness of high-level radioactive waste, it is necessary to develop fuel cladding materials for fast reactors (FRs) in order to achieve high-burnup. Oxide dispersion strengthened (ODS) steel have been studied for use as potential fuel cladding materials in FRs owing to their excellent resistance to swelling and their high-temperature strength in Japan Atomic Energy Agency. It is very important to establish the materials strength standard in order to apply ODS steels as a fuel cladding. Therefore, it is necessary to acquire the mechanical properties such as tensile, creep rupture strength tests and so on. In this study, tensile and creep rupture strengths of 9Cr-ODS steel claddings were evaluated using by acquired these data. Because of the phase transformation temperature of 9Cr-ODS steel, temperature range for the evaluation was divided into two ones at AC1 transformation temperature of 850C.
synchrotron radiation observation of deformation and annealing processes of aluminum single crystalShiro, Ayumi*; Okada, Tatsuya*; Shobu, Takahisa
Mechanical Engineering Journal (Internet), 8(6), p.21-00106_1 - 21-00106_8, 2021/12
The objective of the present study was to carry out observations of deformation and annealing processes of aluminum single crystals using a synchrotron radiation X-rays at SPring-8. Al single-crystalline samples having a 111 orientation parallel to the longitudinal direction were grown by a Bridgman method. The samples were deformed in tension to a nominal strain of 0.08 at room temperature using an in-line tensioning apparatus. Post-deformation annealing at 480 C was subsequently carried out in the same apparatus. A two-dimensional detector was used to detect multiple diffracted beams from the sample during the deformation and annealing processes. The volume irradiated by the X-ray beam was found to be composed of three regions having a small orientation difference, which was attributable to sub-grained microstructures of the sample. Detailed analyses of a diffraction spot intensity showed that the sub-grained microstructures were surpassed by dislocated microstructures with the increase in the tensile strain. During the post-deformation annealing, diffraction spots from a recrystallized grain first appeared at 180 s after the temperature reached 480 C. Coexistence of diffraction spots from the deformation matrix and recrystallized grain lasted only for about 22 s in the irradiated volume. The migration rate of the boundary between the deformation matrix and recrystallized grain was estimated to be of the order of several micrometers/s.
Yano, Yasuhide; Tanno, Takashi; Oka, Hiroshi; Otsuka, Satoshi; Kaito, Takeji
Journal of Nuclear Materials, 555, p.153105_1 - 153105_8, 2021/11
Times Cited Count：1 Percentile：16.35(Materials Science, Multidisciplinary)The aim of this study was to evaluate the tensile properties and microstructures of dissimilar welds between 11Cr-ferritic/martensitic steel and 316 stainless steel after thermal aging at temperatures between 400 and 600C up to 30,000 h. Characterization of microstructure was carried out by scanning electron microscopy and transmission electron microscopy. Microstructural analysis showed that the microstructure in the weld metals consisted of lath martensite containing a small amount of residual austenite. Thermal aging hardening of WMs occurred at 400 and 450C due to the effects of both a-a' phase separation and G-phase precipitation. However, there was no significant change in the total elongation, and fracture surfaces indicated that very fine dimpled rupture was predominant rather than the cleavage rupture. It was suggested that lath martensite phases enhanced the tensile strength due to phase separation, while residual austenite played a role in keeping elongation as a soft phase.
Harjo, S.; Kawasaki, Takuro; Tsuchida, Noriyuki*; Morooka, Satoshi; Gong, W.
Tetsu To Hagane, 107(10), p.887 - 896, 2021/10
Times Cited Count：0 Percentile：0(Metallurgy & Metallurgical Engineering)Harjo, S.
Kensa Gijutsu, 26(9), p.9 - 13, 2021/09
no abstracts in English
Yano, Yasuhide; Tanno, Takashi; Otsuka, Satoshi; Kaito, Takeji; Ukai, Shigeharu*
Materials Transactions, 62(8), p.1239 - 1246, 2021/08
Times Cited Count：5 Percentile：41.35(Materials Science, Multidisciplinary)The FeCrAl-ODS alloy claddings were manufactured and Vickers hardness, ring tensile tests and TEM observations of these claddings were performed to investigate the effects of thermal aging at 450 C for 5,000 and 15,000 h. The age-hardening of all FeCrAl-ODS alloy cladding was found. In addition, the significant increase in tensile strength was accompanied by much larger loss of ductility. It was suggested that this age-hardening behavior was attributed to the (Ti, Al)-enriched phase (
' phase) and the 
' phase precipitates (content of Al is 
7 wt%). In comparison with FeCrAl-ODS alloys with almost same chemical compositions, there was significant age-hardening in both alloys. However, the extrusion bar with no-recrystallized structures was keeping good ductility. It was suggested that this different behavior of reduction ductility was attributed to the effects of grain boundaries, dislocation densities and specimen preparation direction.
Kim, J. G.*; Bae, J. W.*; Park, J. M.*; Woo, W.*; Harjo, S.; Lee, S.*; Kim, H. S.*
Metals and Materials International, 27(2), p.376 - 383, 2021/02
Times Cited Count：9 Percentile：51.51(Materials Science, Multidisciplinary)Sugaya, Naoto; Okada, Yuji; Nishimura, Arashi; Sonobe, Hiroshi; Kimura, Nobuaki; Kimura, Akihiro; Hanawa, Yoshio; Nemoto, Hiroyoshi
JAEA-Testing 2020-004, 67 Pages, 2020/08
JAEA-Testing-2020-004.pdf:8.17MB
In the Japan Materials Testing Reactor (JMTR), the leakage accidents of radioactive waste liquid were occurred from the tanks and pipes of the liquid waste disposal facility in the JMTR tank-yard building in JFY2014. In order to respond to the accident, the tanks and pipes were replaced from JFY2016 to 2019. On the other hand, a lot of cracks were occurred on the concreate wall of the tank-yard building when the frame structure supports were fixed to the concrete wall in the replacement work. Thus, it is necessary to repair the concreate wall of the tank-yard building. Especially, some cracks with swelling (cone-shaped fracture) were raised around some anchor bolts (the post-installed chemical anchor bolts) fixed the frame structure supports. The repairing method for the cone-shaped fracture of the concrete wall is standardized, but there was no reference value of tensile strength for the validation of the post-installed chemical anchor bolts after the repairing method. In this report, the repairing method was selected for the cone-shaped fracture on the concreate wall and the reference value of tensile strength for the validation of the post-installed chemical anchor bolts by this repairing method. The mock-ups for repairing cone-shaped fracture were fabricated by the selected repairing method and the tensile tests of the post-installed chemical anchor bolts were performed. From the results, the validation of the repairing method was obtained in this test and it was obvious the repairing of cone-shaped fracture is preferable method for the concreate wall of the JMTR tank-yard building.
Saito, Shigeru; Suzuki, Kazuhiro; Hatakeyama, Yuichi; Suzuki, Miho; Dai, Y.*
Journal of Nuclear Materials, 534, p.152146_1 - 152146_16, 2020/06
Times Cited Count：1 Percentile：12.16(Materials Science, Multidisciplinary)A post-irradiation examination (PIE) was performed on the tensile specimens prepared from the MEGAPIE (MEGAwatt Pilot Experiment) target which were irradiated in flowing lead-bismuth eutectic (LBE). Thicknesses of the specimens were over two times larger than that of the standard specimen. The PIE revealed that the T91 specimens showed a 1.5-2.0 times larger total elongation (TE) compared to the literature values for a specimen with standard t/w (ratio of thickness to width). It could be suggested that the t/w and TE were strongly correlated. Then, we tried to investigate the effects of the t/w on the TE by comparing unirradiated specimens. We found that there was no t/w dependence on the strength and uniform elongation. On the other hand, the TE increases with increasing t/w. Based on the experimental data, we correlated the TE with various specimens t/w to estimate appropriate TE values, including that for the standard specimen.
Zn
Y
during compression and tensionHarjo, S.; Aizawa, Kazuya; Gong, W.*; Kawasaki, Takuro
Materials Transactions, 61(5), p.828 - 832, 2020/04
Times Cited Count：6 Percentile：37.38(Materials Science, Multidisciplinary)Hosoya, Yoshihiro*; Matsumura, Yuta*; Tomota, Yo*; Onuki, Yusuke*; Harjo, S.
Tetsu To Hagane, 106(3), p.154 - 164, 2020/03
Times Cited Count：2 Percentile：12.73(Metallurgy & Metallurgical Engineering)Lam, T.-N.*; Chou, Y.-S.*; Chang, Y.-J.*; Sui, T.-R.*; Yeh, A.-C.*; Harjo, S.; Lee, S. Y.*; Jain, J.*; Lai, B.-H.*; Huang, E.-W.*
Crystals (Internet), 9(8), p.420_1 - 420_8, 2019/08
Times Cited Count：9 Percentile：67.83(Crystallography)Fukuya, Koji*; Fujii, Katsuhiko*; Chimi, Yasuhiro; Hata, Kuniki
Proceedings of 19th International Conference on Environmental Degradation of Materials in Nuclear Power Systems - Water Reactors (Internet), p.523 - 531, 2019/08
For structural integrity assessment on reactor internals of light water reactors, empirical equations of tensile properties as a function of neutron dose, and trend curves of stress-strain relations of neutron-irradiated austenitic stainless steels was proposed by fitting to recently developed database. The data in the database were obtained from reports of national projects in Japan and open literature, which was summarized in the form of data sheets. The empirical equations for tensile properties were formulated by using a saturation-type formulae. The equations were for CW 316 and SA 304/316 stainless steels in the temperature range of 280-350C and the dose range up to 80 dpa. Stress-strain relation curves were reproduced based on the Swift model. Obtained calculated results by the empirical equations and stress-strain relations were reasonably well fitted to experimental data. The effects of composition and cold-working, etc. on tensile properties were discussed.
Onizawa, Takashi; Nagae, Yuji; Kato, Shoichi; Wakai, Takashi
Zairyo, 66(2), p.122 - 129, 2017/02
The applicability of Modified 9Cr-1Mo steel (ASME Grade 91 steel) as the main structural material in advanced loop-type sodium cooled fast reactor has been explored to enhance the safety, the credibility and the economic competitiveness of fast reactor plants. It is well-known that the steel exhibits cyclic softening behavior. Decrease of tensile and creep strength in softened materials has been already reported by other researchers. This paper discusses the relationship between cyclic softening conditions and high temperature material properties. Grade 91 steel was softened by repeat of plastic strain. The softening behavior could be evaluated by the index of the softening rate. Decrease of tensile and creep strength in softened materials can be evaluated by the softening rate and it depends on the cyclic softening conditions.
Saito, Toru; Okubo, Toshikazu*; Izumi, Keisuke*; Okawa, Yoshinao*; Kobayashi, Norihiro*; Yamazaki, Toru; Kawano, Katsumi; Isono, Takaaki
Teion Kogaku, 50(8), p.400 - 408, 2015/08
Aramid fiber-reinforced plastic (AFRP) has been developed as a structural material that has the advantages of light weight and high strength. In this study, tensile tests were carried out to measure the tensile properties of AFRP rod on the market for reinforcement of concrete at room temperature, 77 K and 4.2 K. Especially at cryogenic temperatures, it is difficult to perform a tensile test of the bar because the specimen slips through the jig grip. To prevent the rod from slipping, tensile tests were carried out with some filling conditions. The applicable and appropriate tensile test conditions were established by modifying the jig grip, treating the surface of the rod and using cryogenic epoxy infill to grip the rod. They were more than 1100 MPa. Additionally, the AFRP rod included a temperature dependence in which the Young's modulus increased as the test temperature decreased. It was confirmed that the Young's modulus increased because aramid fiber was more dominant than epoxy.
Sugiyama, Tomoyuki; Nagase, Fumihisa; Fuketa, Toyoshi
Proceedings of 2005 Water Reactor Fuel Performance Meeting (CD-ROM), p.912 - 932, 2005/10
High burnup fuel cladding can fail due to mechanical interaction with expanding fuel pellet under reactivity initiated accident (RIA) conditions. In order to evaluate the cladding failure limit, investigations to modify ring tensile test have been performed to measure mechanical properties of Zircaloy cladding properly. JAERI developed the test method and geometry minimizing undesirable effects of friction and bending moment in the specimen. Using the modified test method, mechanical properties of unirradiated Zircaloy-4 cladding were evaluated as functions of hydrogen concentration and temperature. For hydrogen concentrations above 700 ppm, obvious increase of ductility is observed with the temperature increase from 300 to 473 K. For hydrogen concentrations below 500 ppm, on the other hand, temperature dependence of ductility is relatively small in the present temperature range from 300 to 573 K.
Okubo, Nariaki; Wakai, Eiichi; Matsukawa, Shingo; Tanigawa, Hiroyasu; Sawai, Tomotsugu; Jitsukawa, Shiro; Onuki, Somei*
Materials Transactions, 46(8), p.1779 - 1782, 2005/08
Times Cited Count：1 Percentile：16.27(Materials Science, Multidisciplinary)no abstracts in English
Igawa, Naoki; Taguchi, Tomitsugu; Yamada, Reiji; Ishii, Yoshinobu; Jitsukawa, Shiro
Journal of Nuclear Materials, 329-333(Part1), p.554 - 557, 2004/08
Times Cited Count：6 Percentile：40.72(Materials Science, Multidisciplinary)no abstracts in English
